SAAB V4 Forum
SAAB V4 Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
 All Forums
 Technical
 General Technical
 brake bleeding - small cap reservoir

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:
UserName:
Password:
Format Mode:
Format:BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List
  
Message:

* HTML is OFF
* Forum Code is ON
Smilies
Smile [:)]Big Smile [:D]Cool [8D]Blush [:I]
Tongue [:P]Evil [):]Wink [;)]Clown [:o)]
Black Eye [B)]Eight Ball [8]Frown [:(]Shy [8)]
Shocked [:0]Angry [:(!]Dead [xx(]Sleepy [|)]
Kisses [:X]Approve [^]Disapprove [V]Question [?]

 
Check here to subscribe to this topic.
  

T O P I C    R E V I E W
green96v4Posted - 11 May 2019 : 12:27:17
Finally got the seal kit in the post from John-Saab and fitted everything back together - now I have another problem/question

I'm getting plenty of piston pressure from the BMC on the bench and we've bleed it on the bench as thoroughly as we can, but now everything's fitted to the car and I'm bleeding the brakes at the calipers and rear cylinders it looks like the brake fluid is getting sucked back up (old skool tube and jam jar) when lifting off the pedal and we're struggling to get any pedal pressure

Should we be pressure bleeding or is there a decent technique for these brakes?

or is this a symptom of a larger problem? (seal kit seemed to fit very well and as previously stated had plenty of "spurt" out on the bench

Thanks in advance
11   L A T E S T    R E P L I E S    (Newest First)
green96v4Posted - 15 May 2019 : 11:06:23
no worries, sorry I wouldn't be any help on this style of BMC
James RanaldiPosted - 14 May 2019 : 22:07:37
Apologies,
My master cylinder is different.
Mine is 1968 with six bolts holding the brake fluid reservoir on.
Thanks

chris steedenPosted - 14 May 2019 : 18:12:19
Is that the one with the 'pin' through it as in position 15 in the above diagram? I'm sorry, but I do not own a V4 or master cylinder to check it out.
James RanaldiPosted - 14 May 2019 : 17:25:14
I have got as far as removing the Nylon Guide Bearing and it is stuck fast.

Did you have to remove this bearing green96v4 ?

If so, how did you do it ?

Cheers

1968 V4 96 ,LHD
1984 99 GL
1992 C900i Convertible
1993 C900 LPT Convertible
James RanaldiPosted - 13 May 2019 : 21:43:21
Most interesting guys as I am just about to fit new seals etc to my 1968 V4 Brake Master Cylinder.( Lockheed).

The youtube link and the vintage Saab Manuals are very helpful.

Thanks again.

1968 V4 96 ,LHD
1984 99 GL
1992 C900i Convertible
1993 C900 LPT Convertible
green96v4Posted - 12 May 2019 : 10:49:50
Hi again

they are supposed to go in opposite directions, there's a YT how to video of a guy rebuilding an MGB BMC, (internals are the same)

https://youtu.be/jvI7cUAvV14

he also states black spring goes in first, but I can't see any plating on either of my springs to tell if one is black or not!

Therefore, I swapped my springs around and bench bled it again and wasn't getting the "sucking" I was getting before, installed it and bled everything again and I have brakes!!! (still needs another bleed as there's a bit too much pedal travel, but I have made progress!)

thanks for your insights on this - I was just about to pull the trigger on an MG BMC and cut my losses!
chris steedenPosted - 11 May 2019 : 20:10:22
Hi, in your top picture the seal tapers do not appear to go the same way. Is this right as it looks like seal (position 10) faces the wrong way.
green96v4Posted - 11 May 2019 : 18:35:37
Ok so a bunch more bleeding and fiddling and I've narrowed the problem down to the front part of the BMC, (I can press the brake pedal and have it work on one front wheel and the opposing back wheel)

there doesn't seem to be any air left, but strangely the circuit that doesn't work "sucks" fluid back up the bleeder tube when the pedal is released.

I've pulled the BMC back off to see what's going on - images below on the seal fitment




Only thing I can see that maybe off is the springs have different compressions, and I'm wondering if I've got those the wrong way around (I have it that the heavier spring is in the middle) but they may have been mixed up


Chris - thanks for the links, I've fitted the later post '71 BMC and servo

Puzzling.....
chris steedenPosted - 11 May 2019 : 13:31:17
If you havent got a manual for the car you can download one from here: http://www.vintagesaabmanuals.org/1960-64-95-96-and-gt.html

See the parts book which depicts the correct assembly.

All the best

Chris
green96v4Posted - 11 May 2019 : 13:24:50
Thanks Chris - that's what we were doing last night, but couldn't get any pedal pressure

I'm pretty sure I fitted everything correctly and did a one-for-one when replacing so I wouldn't get them mixed up, but I may just double check things as you've got me second-guessing myself!

I also have a hand vacuum pump - I'm going to have a go with that today to see if there's just some air being stubborn
chris steedenPosted - 11 May 2019 : 13:16:20
The car bleeds just like any other model of that year i.e. open bleed valve with tube attached terminating in a jar with a bit of brake fluid in the bottom, push brake pedal down, close bleed valve, lift pedal up, open valve, press pedal down etc.etc. Making sure to keep fluid reservoir topped up.
Pressure bleeding is not normally required. Did you fit the master seals facing the right way around? Easy mistake to make.I think that the seal/washer has the tapered side facing inwards or outwards not sure which way, into the cylinder.

Snitz Forums 2000
SAAB V4 Forum© 2000-04 Snitz CommunicationsGo To Top Of Page