SAAB V4 Forum
SAAB V4 Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
 All Forums
 Technical
 General Technical
 Beading in he wing corner. A wee trick.

Note: You must be registered in order to post a reply.
To register, click here. Registration is FREE!

Screensize:
UserName:
Password:
Format Mode:
Format:BoldItalicizedUnderlineStrikethrough Align LeftCenteredAlign Right Horizontal Rule Insert HyperlinkInsert EmailInsert Image Insert CodeInsert QuoteInsert List
  
Message:

* HTML is OFF
* Forum Code is ON
Smilies
Smile [:)]Big Smile [:D]Cool [8D]Blush [:I]
Tongue [:P]Evil [):]Wink [;)]Clown [:o)]
Black Eye [B)]Eight Ball [8]Frown [:(]Shy [8)]
Shocked [:0]Angry [:(!]Dead [xx(]Sleepy [|)]
Kisses [:X]Approve [^]Disapprove [V]Question [?]

 
Check here to subscribe to this topic.
  

T O P I C    R E V I E W
andydeans3Posted - 08 Mar 2019 : 17:55:23
I've just refitted my wings after the various recent welding/restoration work.

I've always had a problem to get the rear wing beading right up tight into the corner below the rear window. This is made worse with fibre glass wings.
Came up with this little trick.

Drill a small hole up at 45 degrees, right into the corner. Go inside the car, and having removed all the trim below the rear window, (Which I had already done), use a Dremel to cut out a little access window, to give you access to the inside end of the hole you just drilled. Do it carefully and it will be hidden behind the trim.

Fit an oblong washer to a long thin countersunk head screw, and use it to pull the beading right up tight into the corner. I made the washer out of a rail meant for 1/4 drive sockets.
See photos below.







1978 LHD SAAB 96
1978 MGB Roadster
2008 LHD "Classic" Renault Twingo
1991 Nissan Figaro
4   L A T E S T    R E P L I E S    (Newest First)
andydeans3Posted - 09 Mar 2019 : 21:45:55
Derek
I think it's easier to get a neat corner with steel wings. My rear wings are currently fibre glass, and it's a lot harder to get that seal neatly in there with fibre glass wings.
I have the steel wings, which are slightly "religious", and plan to have them fettled, re-painted, and re-fitted as a medium term project... ie 1 to 3 years.

As far as rust traps are concerned - I'm very conscious of not making rust traps.
I filled the hole with paint, followed by wax from the inside.
I also spread vaseline on the underside of the rubber seal.

Andy

1978 LHD SAAB 96
1978 MGB Roadster
2008 LHD "Classic" Renault Twingo
1991 Nissan Figaro
DerekPosted - 09 Mar 2019 : 11:51:24
I don't think I'd want to be drilling new rust traps in that area. A hot air gun would likely soften the trim enough to get a neater corner but I'd guess that 99% won't notice a slightly rounded corner anyway.
andydeans3Posted - 09 Mar 2019 : 10:15:47
It might work with a pop rivet, depends how much good metal you've got there. Rivnuts would be better, because it's better to draw the wing in slowly.

I had all my trim out already, and had already cut an access window on both sides, to clean up, and treat the little box section that's hidden there, so it was easy just to drill a small hole through.

If you don't want to remove all your trim, and cut access windows, it would be worth trying a pop rivet, or perhaps a rivnut first.

The key is to use a flat, oblong, slightly dished washer. What you see in my photo is actually part of one of those rails that you keep sockets on. Small, 1/4" drive sockets.


1978 LHD SAAB 96
1978 MGB Roadster
2008 LHD "Classic" Renault Twingo
1991 Nissan Figaro
mellePosted - 08 Mar 2019 : 21:31:46
Great idea, however, wouldn't it be easier to use a pop rivet instead of a screw? No need to cut a window on the inside that way.

www.saabv4.com

Snitz Forums 2000
SAAB V4 Forum© 2000-04 Snitz CommunicationsGo To Top Of Page